hig.sePublications
Change search
Link to record
Permanent link

Direct link
BETA
Sattari, Amir
Publications (10 of 10) Show all publications
Sattari, A. (2015). Investigations of Flow Patterns in Ventilated Rooms Using Particle Image Velocimetry: Applications in a Scaled Room with Rapidly Varying Inflow and over a Wall-Mounted Radiator. (Doctoral dissertation). Stockholm: KTH Royal Institute of Technology
Open this publication in new window or tab >>Investigations of Flow Patterns in Ventilated Rooms Using Particle Image Velocimetry: Applications in a Scaled Room with Rapidly Varying Inflow and over a Wall-Mounted Radiator
2015 (English)Doctoral thesis, comprehensive summary (Other academic)
Abstract [en]

This thesis introduces and describes a new experimental setup for examining the effects of pulsating inflow to a ventilated enclosure. The study aimed to test the hypothesis that a pulsating inflow has potential to improve ventilation quality by reducing the stagnation zones through enhanced mixing. The experimental setup, which was a small-scale, two-dimensional (2D), water-filled room model, was successfully designed and manufactured to be able to capture two-dimensional velocity vectors of the entire field using Particle Image Velocimetry (PIV). Using in-house software, it was possible to conclude that for an increase in pulsation frequency or alternatively in the flow rate, the stagnation zones were reduced in size, the distribution of vortices became more homogeneous over the considered domain, and the number of vortices in all scales had increased. Considering the occupied region, the stagnation zones were moved away in a favorable direction from a mixing point of view. In addition, statistical analysis unveiled that in the far-field occupied region of the room model, stronger eddies were developed that we could expect to give rise to improved mixing. As a fundamental experimental study performed in a 2D, small-scale room model with water as operating fluid, we can logically conclude that the positive effect of enhanced mixing through increasing the flow rate could equally be accomplished through applying a pulsating inflow.

In addition, this thesis introduces and describes an experimental setup for study of air flow over a wall-mounted radiator in a mockup of a real room, which has been successfully designed and manufactured. In this experimental study, the airflow over an electric radiator without forced convection, a common room-heating technique, was measured and visualized using the 2D PIV technique. Surface blackening due to particle deposition calls for monitoring in detail the local climate over a heating radiator. One mechanism causing particle deposition is turbophoresis, which occurs when the flow is turbulent. Because turbulence plays a role in particle deposition, it is important to identify where the laminar flow over radiator becomes turbulent. The results from several visualization techniques and PIV measurements indicated that for a room with typical radiator heating, the flow over the radiator became agitated after a dimensionless length, 5.0–6.25, based on the radiator thickness.

Surface properties are among the influencing factors in particle deposition; therefore, the geometrical properties of different finishing techniques were investigated experimentally using a structured light 3D scanner that revealed differences in roughness among different surface finishing techniques. To investigate the resistance to airflow along the surface and the turbulence generated by the surfaces, we recorded the boundary layer flow over the surfaces in a special flow rig, which revealed that the types of surface finishing methods differed very little in their resistance and therefore their influence on the deposition velocity is probably small. 

Abstract [sv]

Det övergripande syftet med den första studien i avhandlingen var att undersöka hypotesen att ett pulserande inflöde till ett ventilerade utrymme har en potential till att förbättra ventilationens kvalitet genom att minska stagnationszoner och därigenom öka omblandningen. För genomförande av studien byggdes en experimentuppställning i form av en tvådimensionell (2D) småskalig modell av ett ventilerat rum. Strömningsmediet i modellen var vatten. Det tvådimensionella hastighetsfältet registrerades över hela modellen med hjälp av Particle Image Velocimetry (PIV). Vid ett stationärt tillflöde bildas ett stagnationsområde i centrum av rumsmodellen. Vid ett pulserade inflöde genererades sekundära virvlar. Med en egen utvecklad programvara var det möjligt att kvantifiera statistiken hos virvlarna. Det pulserade inflödet gjorde att inom området där det vid stationärt tillflöde fanns en stagnationszon ökade antalet virvlar i alla storlekar och fördelningen av virvlar blev mera homogen än tidigare. Detta kan förväntas ge upphov till förbättrad omblandning. Baserat på en grundläggande experimentell studie utförd i en småskalig tvådimensionell rumsmodell med vatten som strömningsmedium kan vi logiskt dra slutsatsen att ett pulserande tilluftsflöde har en potential att förbättra omblandningen. 

I en fortsatt studie i avhandlingen visuliserades och mättes hastighetsfältet och därefter beräknades statistiska värden av exempelvis medelhastighet, standardavvikelse och skjuvspänning hos hastighetsfluktuationerna i luftströmmen över en väggmonterad radiator med 2D-PIV-teknik.  Bakgrunden till studien är att en bidragande orsak till partikelavsättning på väggytor är turbofores som uppträder vid en turbulent luftström. Studien genomfördes genom uppbyggnad av en fullskalig rumsmodell. Eftersom turbulens spelar en roll vid partikelavsättning genom turbofores är det viktigt att identifiera var det laminära flödet över radiatorn blir turbulent. Resultaten baserat på visualisering och PIV-mätningar indikerade att, för ett rum med denna typ av radiatoruppvärmning, blev flödet över radiatorn turbulent efter en dimensionslös längd lika med 5,0‒6,25 gånger radiatorns tjocklek.

Ytors egenskaper är viktiga vid partikelavsättning. Därför har de geometriska egenskaperna hos några olika metoder för ytbehandling undersökts experimentellt med hjälp av en scanner för strukturerat 3D-ljus. Resultaten visar på skillnader i ytråhet hos de olika ytbehandlingsmetoderna. För att undersöka motståndet mot luftströmning längs ytan och den turbulens som genereras av ytorna registrerade vi gränsskiktsflödet över ytorna i en speciell luftströmningsrigg. Detta påvisade att motståndet hos de olika typerna av ytbehandlingsmetoder skilde sig mycket litet åt och därför är troligt vid deras påverkan på depositionshastigheten mycket liten. 

Place, publisher, year, edition, pages
Stockholm: KTH Royal Institute of Technology, 2015. p. vi, 38
Series
TRITA-IES ; 2015:02
Keywords
Particle Image Velocimetry (PIV), experimental study, structured light 3D scanning system, ventilation, varying flow rate, room model, wall-mounted radiator, air, water, flow, Particle Image Velocimetry (PIV), experimentell studie, scanningsystem för strukturerat 3D-ljus, ventilation, varierande tilluftsflöde, rumsmodell, väggmonterad radiator
National Category
Other Engineering and Technologies not elsewhere specified Civil Engineering Mechanical Engineering
Research subject
Engineering Mechanics; Civil and Architectural Engineering; Energy Technology
Identifiers
urn:nbn:se:hig:diva-19390 (URN)978-91-7595-600-8 (ISBN)
Public defence
2015-06-10, Hall F3, Lindstedtsvägen 26, Stockholm, 15:40 (English)
Opponent
Supervisors
Available from: 2015-05-27 Created: 2015-05-27 Last updated: 2018-03-13Bibliographically approved
Sattari, A. (2015). Particle Image Velocimetry Visualization and measurement of Air Flow over a Wall-Mounted Radiator. The International Journal of Ventilation, 14(3), 289-302
Open this publication in new window or tab >>Particle Image Velocimetry Visualization and measurement of Air Flow over a Wall-Mounted Radiator
2015 (English)In: The International Journal of Ventilation, ISSN 1473-3315, E-ISSN 2044-4044, Vol. 14, no 3, p. 289-302Article in journal (Refereed) Published
Abstract [en]

A common room-heating technique involves the use of a wall-mounted radiator without forced convection. The cold surrounding air passes adjacent to the warm surfaces of the radiator where it absorbs heat and gains momentum to rise along the wall surface and finally circulate in the entire room. Understanding the properties of heated airflows is important for several purposes. To understand the flow process it is important to identify where the transition from laminar to turbulent flow occurs and to quantify the turbulent fluctuations. With the objective to characterize the airflow in the vicinity of wall surfaces, the local climate over the radiator was visualized and measured using a two-dimensional particle image velocimetry technique. The PIV technique yields 2D vector fields of the flow. The resulting vector maps were properly validated and post-processed using in-house software to provide the average streamlines and other statistical information such as standard deviation, average velocity, and covariance of the entire vector field. The results show that, for a room with a typical heating power, the airflow over the radiator becomes agitated after an ordinate of N = 5 - 6.25 over the radiator upper level, in which N is the dimensionless length based on the thickness of the radiator. Practical problems encountered in near-wall PIV measurements include generating a homogeneous global seeding that makes it possible to study both plume and entraining region, as well as optical problems due to near-surface laser reflection that makes the measurement process more complicated.

Keywords
Air circulation, Airflow, Heating radiator, Particle image velocimetry (PIV), Turbulence, Velocity field
National Category
Other Engineering and Technologies not elsewhere specified
Identifiers
urn:nbn:se:hig:diva-19392 (URN)2-s2.0-84951072805 (Scopus ID)
Funder
Swedish Energy Agency, 2011-002440
Available from: 2015-05-25 Created: 2015-05-27 Last updated: 2018-03-13Bibliographically approved
Sattari, A. & Sandberg, M. (2014). Particle image velocimetry (PIV) visualization of air flow over a wall-mounted radiator. In: : . Paper presented at ROOMVENT, The 13th International Conference on Air Distribution in Rooms, October 19-22, São Paulo, Brazil.
Open this publication in new window or tab >>Particle image velocimetry (PIV) visualization of air flow over a wall-mounted radiator
2014 (English)Conference paper, Published paper (Refereed)
Abstract [en]

A common room heating technique is to use a wall-mounted radiator without forced convection. The cold surrounding air passes adjacent to the warm surfaces of the radiator, gets heated, and the buoyancy difference gives this heated air a momentum to rise along the wall surface (as plume) and finally circulate and get mixed into the whole room. The properties of heated plumes are important for assessing the risk of soiling of the wall surfaces through particle deposition driven by thermophoresis and turbophoresis. It is important to identify where there is a transition from laminar to turbulent flow. With the objective to characterize the plume of heated air flow in the vicinity of wall surface, the airflow over the radiator is visualized and measured using the two-dimensional Particle Image Velocimetry (2D PIV) technique. The PIV technique yields two-dimensional vector fields of the flow. The resulted vector maps are size and peak validated and post processed using in house developed software to provide the average streamlines. In the near wall PIV measurements there are practical problems; generating a homogeneous global seeding that makes it possible to study both the plume and the surrounding entrainment region, and optical problems due to strong laser reflection from the wall surface which limits the investigation area. These issues are dealt with in the present study. In addition to visualization with PIV, visualization with a CMOS video camera was also conducted.

Keywords
radiator, PIV, thermophoresis, turbophoresis, visualization
National Category
Other Engineering and Technologies not elsewhere specified
Identifiers
urn:nbn:se:hig:diva-19391 (URN)
Conference
ROOMVENT, The 13th International Conference on Air Distribution in Rooms, October 19-22, São Paulo, Brazil
Available from: 2014-08-13 Created: 2015-05-27 Last updated: 2018-03-13Bibliographically approved
Fallenius, B. E. .., Sattari, A., Fransson, J. & Sandberg, M. (2013). Experimental study on the effect of pulsating inflow to an enclosure for improved mixing. International Journal of Heat and Fluid Flow, 44, 108-119
Open this publication in new window or tab >>Experimental study on the effect of pulsating inflow to an enclosure for improved mixing
2013 (English)In: International Journal of Heat and Fluid Flow, ISSN 0142-727X, E-ISSN 1879-2278, Vol. 44, p. 108-119Article in journal (Refereed) Published
National Category
Engineering and Technology
Identifiers
urn:nbn:se:hig:diva-15186 (URN)10.1016/j.ijheatfluidflow.2013.05.004 (DOI)000329594600009 ()2-s2.0-84888432075 (Scopus ID)
Available from: 2013-09-10 Created: 2013-09-10 Last updated: 2018-03-13Bibliographically approved
Sattari, A. & Sandberg, M. (2013). PIV Study of Ventilation Quality in Certain Occupied Regions of a Two-Dimensional Room Model with Rapidly Varying Flow Rates. The International Journal of Ventilation, 12(2), 187-194
Open this publication in new window or tab >>PIV Study of Ventilation Quality in Certain Occupied Regions of a Two-Dimensional Room Model with Rapidly Varying Flow Rates
2013 (English)In: The International Journal of Ventilation, ISSN 1473-3315, E-ISSN 2044-4044, Vol. 12, no 2, p. 187-194Article in journal (Refereed) Published
Abstract [en]

The use of supply jet flows is the most common type of air distribution for general ventilation. Usually the supply flow rate is constant or slowly varying (VAV-systems) to cope with a varying load. A novel air distribution method, with the potential to reduce stagnation and to increase the ventilation efficiency, is to introduce rapid flow variations (pulsations). This paper reports on a fundamental study of this type of air distribution. The purpose of the study was to explore the effect of flow variations on stagnant zones and the levels of the turbulent kinetic energy and the relative turbulence intensity. A small scale room model is used that consists of an enclosure with a ventilation supply at the bottom and an extract at the top of the opposite wall. Water was used as an operating fluid and the model had a design which mainly generated a two-dimensional flow. The size of the model made it possible to investigate the two-dimensional velocity vector field using the Particle Image Velocimetry (PIV) method in regions corresponding to occupied regions. Further post processing was conducted from the resulting vector fields. The comparison between cases of constant inflow and pulsated inflow (flow variations with frequency of 0.5 Hz) was conducted for three domains: two belonging to the far-field occupied zone and one belonging to the near-field, downstream of the supply wall jet.

Keywords
PIV, ventilation, varying flow rate, flow
National Category
Building Technologies
Identifiers
urn:nbn:se:hig:diva-15188 (URN)000329605700011 ()
Available from: 2013-09-10 Created: 2013-09-10 Last updated: 2018-03-13Bibliographically approved
Sandberg, M., Sattari, A. & Mattsson, M. (2013). Plaster finishes in historical buildings: Measurements of surface structure, roughness parameters and air flow characteristics. In: A. Troi and E. Luchi. (Ed.), Conference proceedings: Cultural heritage preservation – 3rd European Workshop on Cultural Heritage Preservation: . Paper presented at Cultural heritage preservation – 3rd European Workshop on Cultural Heritage Preservation (EWCHP), Bozen, Italy, September 16-17, 2013 (pp. 69-75).
Open this publication in new window or tab >>Plaster finishes in historical buildings: Measurements of surface structure, roughness parameters and air flow characteristics
2013 (English)In: Conference proceedings: Cultural heritage preservation – 3rd European Workshop on Cultural Heritage Preservation / [ed] A. Troi and E. Luchi., 2013, p. 69-75Conference paper, Published paper (Refereed)
Abstract [en]

Soiling of surfaces in historical buildings by deposition of particles is a common problem. Minimizing soiling is an important goal for conservation of structures and objects. The surfaces give rise to an interference with the air motions along the surfaces. Properties of surfaces may therefore influence the particle deposition. It is well known that with increasing roughness of the surfaces the particle deposition rate increases. The properties of surfaces in historical buildings are not well documented.  We have investigated samples of surfaces finished by wood float finish, steel float finish and brushed finish. As a reference we have used an MDF board. The geometrical properties of the surfaces have been documented by using the stripe projection method. The resistance to airflow along the surface and the turbulence generated by the surfaces has been investigated by recording the boundary layer flow over the surfaces in a special flow rig. The work reported is part of a project where the process of soiling is studied both in laboratory and in field studies. The air velocity adjacent to the surfaces will be recorded with both PIV (Particle Image Velocimetry) and hot-wire technique. The temperature gradient close to the walls will be recorded with cold-wire technique.

Keywords
Soiling, Plasters, Particle deposition, Surface structure, Surface roughness, Churches.
National Category
Building Technologies
Identifiers
urn:nbn:se:hig:diva-15411 (URN)978-88-88307-26-8 (ISBN)
Conference
Cultural heritage preservation – 3rd European Workshop on Cultural Heritage Preservation (EWCHP), Bozen, Italy, September 16-17, 2013
Projects
Church project
Funder
Swedish Energy Agency, 2011-002440
Available from: 2013-09-24 Created: 2013-09-24 Last updated: 2018-03-13Bibliographically approved
Sattari, A., Ahmadi Moghaddam, E. & Sandberg, M. (2012). Industrial nanoparticles health risks and advantages of a decent industrial ventilation system in reducing the related risks. Paper presented at The 10th international conference on industrial ventilation.
Open this publication in new window or tab >>Industrial nanoparticles health risks and advantages of a decent industrial ventilation system in reducing the related risks
2012 (English)Conference paper, Poster (with or without abstract) (Refereed)
Abstract [en]

With the fast-growing use of nanoparticles (NPs) in a wide range of production andmanufacturing processes, and great health and environmental risks associated to NPs, it is important totreat the industry-produced NPs in a proper way. Ventilation of industrial workplaces lies within theconcept of sustainability challenges for the development of nanoproducts. Due to the decreased grainsize of material to nano limits and thus the appearance of either new or changed properties, health riskof workers in such environments is critical concerning the complicated and unknown characteristicsof nanoparticles. There is great evidence over the past few years that ultrafine particles and especiallyNPs in the breathing air are strong toxins. Different mitigation measures for air-borne nanoparticles inindustrial workplaces are substitution, engineering controls such as ventilation and provision of personalprotective equipment. In this paper selection criteria for ventilation systems and different ventilationmethods (hood ventilation and global enclosure/room ventilation systems) as engineering controlsof nanoparticles within industrial enclosures will be reviewed. Novel methods for improvement ofventilation efficiency in general and industrial work places with an eye on ventilation of nanoparticleswill be presented.

Keywords
industrial ventilation, work place, nanoparticles, health risks
National Category
Nano Technology Fluid Mechanics and Acoustics Health Sciences
Identifiers
urn:nbn:se:hig:diva-13485 (URN)
Conference
The 10th international conference on industrial ventilation
Available from: 2012-12-05 Created: 2012-11-30 Last updated: 2018-03-13Bibliographically approved
Sattari, A. & Sandberg, M. (2012). Piv study of ventilation quality incertain occupied regions of a 2d room model with rapidly varying flow rates. In: : . Paper presented at The 10th international conference on industrial ventilation.
Open this publication in new window or tab >>Piv study of ventilation quality incertain occupied regions of a 2d room model with rapidly varying flow rates
2012 (English)Conference paper, Oral presentation only (Refereed)
Abstract [en]

The use of supply jet flows is the most common type of air distribution for general ventilation inindustrial premises. Usually the supply flow rate is constant or slow varying (VAV-systems) to copewith a varying load. A novel air distribution method, with the potential to reduce stagnation and toincrease the ventilation efficiency, is to introduce rapid flow variations (pulsations). In the paper wereport on a fundamental study of this type of air distribution. The purpose of the study was to explorethe effect on stagnant zones and the levels of the kinetic energy and the relative turbulence intensity.The study was conducted in a small-scale, two-dimensional (2-D) room model with water as operatingfluid. The size of the model made it possible to investigate the 2-D velocity vector field in certainoccupied regions using Particle Image Velocimetry (PIV) method and further consequent analyseshave been done from the resulted vector fields. The comparison between cases of constant inflow andpulsated inflow (flow variations with frequency of 0.5 Hz) have been conducted for three domains,two belonging to the far-field occupied zone and one belonging to the near-field, downstream of thesupply wall jet.

Keywords
PIV, ventilation, varying flow rate, room model
National Category
Fluid Mechanics and Acoustics
Identifiers
urn:nbn:se:hig:diva-13483 (URN)
Conference
The 10th international conference on industrial ventilation
Available from: 2012-12-05 Created: 2012-11-30 Last updated: 2018-03-13Bibliographically approved
Sattari, A., Fallenius, B. E. G., Fransson, J. H. M. & Sandberg, M. (2011). PIV Visualisation Study in a Two-Dimensional Room Model with Rapid Time Varying Ventilation Flow Rates. In:  . Paper presented at ROOMVENT 2011, Trondheim, Norway, June 19-22, 2011. tapir academic press
Open this publication in new window or tab >>PIV Visualisation Study in a Two-Dimensional Room Model with Rapid Time Varying Ventilation Flow Rates
2011 (English)In:  , tapir academic press , 2011Conference paper, Published paper (Refereed)
Abstract [en]

Optimal control of inlet jet flows is of wide applicative interest in order to enhance mixing and reduce stagnation in a ventilated room. The general approach in mechanical ventilation is to use a constant flow rate forced convection system providing the ventilation air. This type of ventilation may cause several problems such as draught, stagnation at certain occupied locations, and subsequently low ventilation efficiencies. An alternative to increase the ventilation quality that has been of interest in this study is to introduce flow variations, which is considered as a potential to reduce stagnation and increase efficiency of the ventilation. The study was conducted as a model experiment in a small-scale, two-dimensional (2-D) room model with dimensions 30´20´0.9 cm3 with water as operating fluid. The size of the model made it possible to investigate the 2-D velocity vector field within the entire room using Particle Image Velocimetry (PIV) method and further consequent dynamical and statistical analyses have been done from the resulted PIV vector fields. The comparison between cases of constant flow rate and flow variations have been conducted for the cases of two set of base flow rates and for each one, the cases of constant flow rate and flow variations with frequencies of 0.3, 0.4 and 0.5 Hz, is considered. In this investigation we show that the calm region, with a large stagnation zone, without pulsating inflow condition becomes more active in the sense that the stagnation points are moved and that the small-scale structures are grown for increasing pulsation frequency.

Place, publisher, year, edition, pages
tapir academic press, 2011
Keywords
PIV, room model, ventilation, varying flow rate
National Category
Engineering and Technology
Identifiers
urn:nbn:se:hig:diva-10543 (URN)978-82-519-2812-0 (ISBN)
Conference
ROOMVENT 2011, Trondheim, Norway, June 19-22, 2011
Available from: 2011-09-29 Created: 2011-09-29 Last updated: 2018-03-13Bibliographically approved
Santhi Pechsiri, J., Sattari, A., Garza Martinez, P. & Xuan, L. (2010). A Review of the Climate-Change-Impacts’ Rates of Change in the Arctic. Journal of Environmental Protection, 1(1), 59-69
Open this publication in new window or tab >>A Review of the Climate-Change-Impacts’ Rates of Change in the Arctic
2010 (English)In: Journal of Environmental Protection, ISSN 2152-2197, E-ISSN 2152-2219, Vol. 1, no 1, p. 59-69Article in journal (Refereed) Published
Abstract [en]

Climate Change is a global phenomenon that has a global scale impact. The current trend of climate change towards the warming of the globe has resulted in various changes in the geological, climatology, social, economical, and biological processes worldwide. Temperature of the globe has increased due to various factors, but anthropogenic plays a major contribution through the heavy input of Greenhouse gases. One of the world’s most remote regions that have been affected by most of the anthropogenic stresses on environmental services is the Arctic Region. The Arctic Region has shown various drastic changes and has shown to be effected by various anthropogenic activities that take place elsewhere. These changes include the ozone hole (resulting from ozone degrading compound emitted heavily by anthropogenic demands ), the accumulation of various persistent and volatile pollutants (i.e. POPs) , and the meltdown of the polar ice (among others) . These drastic changes are well perceived and well projected for future preparations. However, the question still remains if these impacts would only accelerate change. This paper aims to discuss if these changes are accelerating or happening at a constant rate. In addition, this paper aims to only focus on changes due to global warming and climate changes phenomenon.

Keywords
Climate Change Impacts, Rates of Change, Causal Network, Arctic Ecosystems
National Category
Earth and Related Environmental Sciences
Identifiers
urn:nbn:se:hig:diva-10545 (URN)10.4236/jep.2010.11008 (DOI)
Available from: 2011-09-29 Created: 2011-09-29 Last updated: 2018-03-13Bibliographically approved
Organisations

Search in DiVA

Show all publications