hig.sePublikasjoner
Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • harvard-cite-them-right
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • sv-SE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • de-DE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Investigation of flow and heat transfer of an impinging jet in a cross-flow for cooling of a heated cube
Högskolan i Gävle, Institutionen för teknik och byggd miljö, Ämnesavdelningen för energi- och maskinteknik.
Högskolan i Gävle, Institutionen för teknik och byggd miljö, Ämnesavdelningen för energi- och maskinteknik.ORCID-id: 0000-0003-3472-4210
2006 (engelsk)Inngår i: Journal of Electronic Packaging, ISSN 1043-7398, E-ISSN 1528-9044, Vol. 128, nr 2, s. 150-156Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

The current trends toward the greater functionality of electronic devices are resulting in a steady increase in the amount of heat dissipated from electronic components. Forced channel flow is frequently used to remove heat at the walls of the channel where a PCB with a few high heat dissipating components is located. The overall cooling strategy thus must not only match the overall power dissipation load, but also address the requirements of the "hot" components. In order to cool the thermal load with forced channel flow, excessive flow rates will be required. The objective of this study is to investigate if targeted cooling systems, i.e., an impinging jet in combination with a low velocity channel flow, can improve the thermal performance of the system. The steady-state three-dimensional (3-D) model is developed with the Reynolds-Stress-Model (RSM) as a turbulence model. The geometrical case is a channel with a heated cube in the middle of the base plate and two inlets, one horizontal channel flow, and one vertical impinging jet. The numerical model is validated against experimental data obtained from three well-known cases, two cases with an impinging jet on a flat heated plate, and one case with a heated cube in a single channel flow. The effects of the jet Re and jet to-cross-flow velocity ratio are investigated. The airflow pattern around the cube and the surface temperature of the cube as well as the mean values and local distributions of the heat transfer coefficient are presented.

sted, utgiver, år, opplag, sider
2006. Vol. 128, nr 2, s. 150-156
Emneord [en]
Impingement, Matrix
HSV kategori
Identifikatorer
URN: urn:nbn:se:hig:diva-2426DOI: 10.1115/1.2188948ISI: 000238602900009OAI: oai:DiVA.org:hig-2426DiVA, id: diva2:119088
Tilgjengelig fra: 2006-08-21 Laget: 2006-08-21 Sist oppdatert: 2018-03-13bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekst

Personposter BETA

Rundström, DanielMoshfegh, Bahram

Søk i DiVA

Av forfatter/redaktør
Rundström, DanielMoshfegh, Bahram
Av organisasjonen
I samme tidsskrift
Journal of Electronic Packaging

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 219 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • harvard-cite-them-right
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • sv-SE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • de-DE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf