hig.sePublications
Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • harvard-cite-them-right
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • sv-SE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • de-DE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
Investigation of flow and heat transfer of an impinging jet in a cross-flow for cooling of a heated cube
University of Gävle, Department of Technology and Built Environment, Ämnesavdelningen för energi- och maskinteknik.
University of Gävle, Department of Technology and Built Environment, Ämnesavdelningen för energi- och maskinteknik.ORCID iD: 0000-0003-3472-4210
2006 (English)In: Journal of Electronic Packaging, ISSN 1043-7398, E-ISSN 1528-9044, Vol. 128, no 2, p. 150-156Article in journal (Refereed) Published
Abstract [en]

The current trends toward the greater functionality of electronic devices are resulting in a steady increase in the amount of heat dissipated from electronic components. Forced channel flow is frequently used to remove heat at the walls of the channel where a PCB with a few high heat dissipating components is located. The overall cooling strategy thus must not only match the overall power dissipation load, but also address the requirements of the "hot" components. In order to cool the thermal load with forced channel flow, excessive flow rates will be required. The objective of this study is to investigate if targeted cooling systems, i.e., an impinging jet in combination with a low velocity channel flow, can improve the thermal performance of the system. The steady-state three-dimensional (3-D) model is developed with the Reynolds-Stress-Model (RSM) as a turbulence model. The geometrical case is a channel with a heated cube in the middle of the base plate and two inlets, one horizontal channel flow, and one vertical impinging jet. The numerical model is validated against experimental data obtained from three well-known cases, two cases with an impinging jet on a flat heated plate, and one case with a heated cube in a single channel flow. The effects of the jet Re and jet to-cross-flow velocity ratio are investigated. The airflow pattern around the cube and the surface temperature of the cube as well as the mean values and local distributions of the heat transfer coefficient are presented.

Place, publisher, year, edition, pages
2006. Vol. 128, no 2, p. 150-156
Keyword [en]
Impingement, Matrix
National Category
Energy Engineering
Identifiers
URN: urn:nbn:se:hig:diva-2426DOI: 10.1115/1.2188948ISI: 000238602900009OAI: oai:DiVA.org:hig-2426DiVA, id: diva2:119088
Available from: 2006-08-21 Created: 2006-08-21 Last updated: 2018-03-13Bibliographically approved

Open Access in DiVA

No full text in DiVA

Other links

Publisher's full text

Authority records BETA

Rundström, DanielMoshfegh, Bahram

Search in DiVA

By author/editor
Rundström, DanielMoshfegh, Bahram
By organisation
Ämnesavdelningen för energi- och maskinteknik
In the same journal
Journal of Electronic Packaging
Energy Engineering

Search outside of DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric score

doi
urn-nbn
Total: 218 hits
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • harvard-cite-them-right
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • sv-SE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • de-DE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf