hig.sePublikasjoner
Endre søk
Begrens søket
1 - 3 of 3
RefereraExporteraLink til resultatlisten
Permanent link
Referera
Referensformat
  • apa
  • harvard-cite-them-right
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • sv-SE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • de-DE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Treff pr side
  • 5
  • 10
  • 20
  • 50
  • 100
  • 250
Sortering
  • Standard (Relevans)
  • Forfatter A-Ø
  • Forfatter Ø-A
  • Tittel A-Ø
  • Tittel Ø-A
  • Type publikasjon A-Ø
  • Type publikasjon Ø-A
  • Eldste først
  • Nyeste først
  • Skapad (Eldste først)
  • Skapad (Nyeste først)
  • Senast uppdaterad (Eldste først)
  • Senast uppdaterad (Nyeste først)
  • Disputationsdatum (tidligste først)
  • Disputationsdatum (siste først)
  • Standard (Relevans)
  • Forfatter A-Ø
  • Forfatter Ø-A
  • Tittel A-Ø
  • Tittel Ø-A
  • Type publikasjon A-Ø
  • Type publikasjon Ø-A
  • Eldste først
  • Nyeste først
  • Skapad (Eldste først)
  • Skapad (Nyeste først)
  • Senast uppdaterad (Eldste først)
  • Senast uppdaterad (Nyeste først)
  • Disputationsdatum (tidligste først)
  • Disputationsdatum (siste først)
Merk
Maxantalet träffar du kan exportera från sökgränssnittet är 250. Vid större uttag använd dig av utsökningar.
  • 1.
    Jahedi, Mohammad
    et al.
    Högskolan i Gävle, Akademin för teknik och miljö, Avdelningen för bygg- energi- och miljöteknik, Energisystem.
    Berntsson, Fredrik
    Department of Mathematics, Linköping University, Linköping, Sweden.
    Wren, Joakim
    Department of Management and Engineering, Linköping University, Linköping, Sweden.
    Moshfegh, Bahram
    Högskolan i Gävle, Akademin för teknik och miljö, Avdelningen för bygg- energi- och miljöteknik, Energisystem. Department of Management and Engineering, Linköping University, Linköping, Sweden.
    Transient inverse heat conduction problem of quenching a hollow cylinder by one row of water jets2018Inngår i: International Journal of Heat and Mass Transfer, ISSN 0017-9310, E-ISSN 1879-2189, Vol. 117, s. 748-756Artikkel i tidsskrift (Fagfellevurdert)
    Abstract [en]

    In this study, a two-dimensional linear transition inverse heat conduction problem (IHCP) was solved using the Generalized Minimal Residual Method (GMRES) in quenching process by water jets. The inverse solution method was validated by set of artificial data and solution sensitivity analysis was done on data noise level, regularization parameter, cell size, etc. An experimental study has been carried out on quenching a rotary hollow cylinder by one row of subcooled water jets. The inverse solution approach enabled prediction of surface temperature and heat flux distribution of test specimen in the quenching experiments by using measured internal specimen temperature. Three different boiling curves were defined in the quenching process of a rotary cylinder. Result obtained by the inverse solution showed clear footprint of rotation in surface temperature and heat flux on each revolution of cylinder and temperature variation damping from quenching surface toward interior of specimen.

  • 2.
    Jahedi, Mohammad
    et al.
    Högskolan i Gävle, Akademin för teknik och miljö, Avdelningen för bygg- energi- och miljöteknik, Energisystem.
    Moshfegh, Bahram
    Högskolan i Gävle, Akademin för teknik och miljö, Avdelningen för bygg- energi- och miljöteknik, Energisystem. Division of Energy Systems, Department of Management and Engineering, Linköping University.
    Experimental study of quenching process on a rotating hollow cylinder by one row of impinging jets2017Inngår i: 9th World Conference on Experimental Heat Transfer, Fluid Mechanics and Thermodynamics, 12-15 June, 2017, Iguazu Falls, Brazil, 2017Konferansepaper (Fagfellevurdert)
    Abstract [en]

    Quenching cooling rate of rotary hollow cylinder by one row of water impinging jets has been experimentallystudied. Water jets (d = 8 mm) with sub-cooling 55 to 85°C and Reynolds number 8,006 to 36,738 impinged over rotaryhot hollow cylinder (rotation speed 10 to 70 rpm) with initial temperature 250 to 600°C. Impingement impact angle of row of jets varied between 0 to 135° and jet-to-jet spacing in row patten was 2 to 8d. The results revealed more uniformityon cooling rate of quenching in smaller jet-to-jet spacing (2 and 4d) where wetting front regions are located closer toneighbor jet’s region. By increasing spacing, footprint of annular transition region was highlighted in quenching coolingrate contour. A distinct quenching characteristic was obtained for impingement impact angle of 0° compare to otherangles. With initial temperature above the Leidenfrost temperature, low cooling rate was achieved in film and transitionboiling compare to a steep increase of cooling rate at start of quenching with higher maximum heat transfer for experimentswith initial temperatures less than Leidenfrost temperature. The effect of other parameters on quenching coolingrate was highlighted in film and transition boiling while no significant differences were observed in nucleate boiling.

    Fulltekst (pdf)
    fulltext
  • 3.
    Jahedi, Mohammad
    et al.
    Högskolan i Gävle, Akademin för teknik och miljö, Avdelningen för byggnadsteknik, energisystem och miljövetenskap, Energisystem och byggnadsteknik.
    Moshfegh, Bahram
    Högskolan i Gävle, Akademin för teknik och miljö, Avdelningen för byggnadsteknik, energisystem och miljövetenskap, Energisystem och byggnadsteknik. Department of Management and Engineering, Linköping University.
    Quenching a rotary hollow cylinder by multiple configurations of water-impinging jets2019Inngår i: International Journal of Heat and Mass Transfer, ISSN 0017-9310, E-ISSN 1879-2189, Vol. 137, s. 124-137Artikkel i tidsskrift (Fagfellevurdert)
    Abstract [en]

    Experiments have been conducted to analyze quenching of a hot rotary hollow cylinder by one and two rows of water-impinging jets. Sub-cooled water jets (ΔTsub = 45–85 K) with flow rate 8006 to 36,738 impinged on hollow cylinder with rotation speed 10 to 70 rpm at various initial wall superheat temperatures from 250 to 600ºC. Jet-to-jet and jet-to-surface spacing varied between 4 to 10d and 1.5 to 7d respectively and angular position of impinging jets were tested from 0 to 135º. Effectiveness of the defined parameters on stagnation point’s local average heat flux was found lower in the film and nucleate boiling compare to transition boiling regime where rotation speed had the highest impact. Characteristic of maximum heat flux (MHF) at stagnation point and upwash flow point were analyzed based on surface heat flux, time and temperature corresponding to MHF. Same maximum heat flux levels were captured in the both points which reveals importance of the flow behavior at the upwash flow point. The effectiveness of the parameters to improve average heat transfer was studied based on cooling area of each water impingingjet in the multiple configurations. Higher average heat transfer was obtained by increasing flow rate and subcooling temperature and lower initial wall superheat temperature corresponding to onset of transition boiling regime.

1 - 3 of 3
RefereraExporteraLink til resultatlisten
Permanent link
Referera
Referensformat
  • apa
  • harvard-cite-them-right
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • sv-SE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • de-DE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf