hig.sePublications
Change search
Link to record
Permanent link

Direct link
Publications (10 of 25) Show all publications
Mattsson, K., Eriksson, G., Persson, L., Chilo, J. & Tatar, K. (2026). Efficient finite difference modeling of infrasound propagation in realistic 3D domains: Validation with wind turbine measurements. Applied Acoustics, 243, Article ID 111156.
Open this publication in new window or tab >>Efficient finite difference modeling of infrasound propagation in realistic 3D domains: Validation with wind turbine measurements
Show others...
2026 (English)In: Applied Acoustics, ISSN 0003-682X, E-ISSN 1872-910X, Vol. 243, article id 111156Article in journal (Refereed) Published
Abstract [en]

We present a high-fidelity simulation tool for accurate acoustic modeling across a wide range of applications. The numerical method is based on diagonal-norm Summation-By-Parts (SBP) finite-difference operators, which guarantee linear stability on piecewise curvilinear multi-block grids. Realistic three-dimensional atmospheric and topographic data are directly incorporated into the simulations, and the solver is implemented in CUDA to achieve high computational efficiency. Verification is performed through convergence studies against highly resolved benchmark problems in both two and three spatial dimensions, while validation is carried out using high-quality infrasound measurements from two modern wind farms in Sweden. The results show that modern, large-scale wind turbines generate infrasound levels significantly higher than those reported for older, smaller turbines. These findings advance the understanding of the acoustic characteristics of contemporary wind turbines and provide important guidance for assessing their potential environmental and societal impacts.

Place, publisher, year, edition, pages
Elsevier, 2026
Keywords
Finite difference methods, Infrasound measurement, Infrasound simulations, Validation, Verification
National Category
Other Electrical Engineering, Electronic Engineering, Information Engineering
Identifiers
urn:nbn:se:hig:diva-48810 (URN)10.1016/j.apacoust.2025.111156 (DOI)001618232600001 ()2-s2.0-105021266575 (Scopus ID)
Funder
Swedish Research Council, 2021-05830Swedish Research Council Formas, 2022-00843
Available from: 2025-11-21 Created: 2025-11-21 Last updated: 2026-02-19Bibliographically approved
Tatar, K. & Svenningsson, I. (2026). Investigation of sustainable face milling of austenitic stainless steel: material removal performance and tool modification. The International Journal of Advanced Manufacturing Technology, 142, 349-359
Open this publication in new window or tab >>Investigation of sustainable face milling of austenitic stainless steel: material removal performance and tool modification
2026 (English)In: The International Journal of Advanced Manufacturing Technology, ISSN 0268-3768, E-ISSN 1433-3015, Vol. 142, p. 349-359Article in journal (Refereed) Published
Abstract [en]

This study investigates face milling of austenitic stainless steel under sustainable dry and Minimum Quantity Lubrication (MQL) conditions, with material removal volume (MRV) as the primary response variable. Austenitic stainless steel poses significant machining challenges due to its low thermal conductivity, high ductility, and work hardening tendencies, exacerbating tool wear mechanisms like notching and chipping. A full factorial design of experiments was conducted, varying cutting speed and feed per tooth, to evaluate their effects on MRV. Quadratic regression models were developed, incorporating Box-Cox transformations for improved robustness and predictive accuracy. Monte Carlo simulations were employed to assess robustness and process variability. Results show that dry machining yields a higher MRV (optimal: 250 cm³ at 213 m/min, 0.20 mm/tooth), while MQL provides a higher material removal rate but lower MRV (optimal: 231 cm³ at 170 m/min, 0.32 mm/tooth), illustrating the trade-off between tool life and short-term productivity. Experimental validation with new test conditions confirmed the accuracy and robustness of the regression models, with predictions closely matching observed results within a 95% prediction interval. Monte Carlo simulations further highlighted that dry machining resulted in higher MRV with greater variability, while MQL gave more consistent but lower MRV values. Observations of notch wear and cracks (most plausibly associated with thermal fatigue) under MQL motivated a preliminary tool modification that redirected the MQL jet away from the cutting edge during tool exit, showing up to 25–50% improvement in MRV. These findings contribute to sustainable machining strategies by providing actionable insights into parameter selection for improved efficiency and durability in industrial applications.

Place, publisher, year, edition, pages
Springer, 2026
Keywords
Austenitic stainless steel; Milling; Monte Carlo; MQL; Notch wear; Thermal fatigue; Tool design; Tool wear
National Category
Materials Engineering
Identifiers
urn:nbn:se:hig:diva-48992 (URN)10.1007/s00170-025-17010-8 (DOI)001629717600001 ()2-s2.0-105023980851 (Scopus ID)
Available from: 2025-12-11 Created: 2025-12-11 Last updated: 2026-03-04Bibliographically approved
Svenningsson, I., Tatar, K. & Östby, J. (2026). Mechanisms of Notch Wear Formation in Stainless Steel Turning. Machines, 14(3), Article ID 297.
Open this publication in new window or tab >>Mechanisms of Notch Wear Formation in Stainless Steel Turning
2026 (English)In: Machines, E-ISSN 2075-1702, Vol. 14, no 3, article id 297Article in journal (Refereed) Published
Abstract [en]

Notch wear in austenitic stainless steel turning develops rapidly and remains a key productivity limitation with carbide tools. This work identifies the initiation mechanism of notch wear when turning EN 1.4307 stainless steel using CVD-coated cemented carbide inserts with an Al2O3 top layer. Turning tests were performed under dry conditions, followed by optical wear measurements and chip surface analysis. The tool–chip interface chemistry and material transfer were characterized using SEM/EDS, while high-frequency acoustic emissions were recorded to resolve the dynamics of adhesive events. Thermo-mechanical FEM simulations were conducted to map contact pressure and temperature along the cutting edge. The results show that adhesive wear initiates immediately at engagement and governs notch formation: polluted SiO2 deposits act as an active bonding medium, and repeated bond formation/rupture removes extremely thin flakes of tool and coating material, evidenced by Al2O3 and Ti(C,N) fragments on the chip and by characteristic acoustic cluster waves. A new tool–chip contact model is presented, indicating that high pressure and high temperature within the polluted SiO2 near the chip’s outmost side promote larger, stronger adhesive bonds together with the absence of ceramic particles near the rake in the notch area. Oxidation and diffusion are assumed to be secondary processes that become relevant after local coating loss, while adhesion remains the primary removal mechanism during early and intermediate stages.

Place, publisher, year, edition, pages
MDPI, 2026
Keywords
metal cutting; notch wear; build-up edge (BuE); stainless steel; adhesive wear; SiO2; FEM; acoustic signals
National Category
Mechanical Engineering
Identifiers
urn:nbn:se:hig:diva-49511 (URN)10.3390/machines14030297 (DOI)001727099500001 ()2-s2.0-105034109700 (Scopus ID)
Available from: 2026-03-13 Created: 2026-03-13 Last updated: 2026-04-13Bibliographically approved
Tatar, K., Dasyam, V. S. & Chilo, J. (2026). Unit Infrasound Activity: A Metric for Quantifying Signal Strength, Regularity, and Persistence in the 0.5–10 Hz Band. Signals, 7(5), Article ID 101.
Open this publication in new window or tab >>Unit Infrasound Activity: A Metric for Quantifying Signal Strength, Regularity, and Persistence in the 0.5–10 Hz Band
2026 (English)In: Signals, E-ISSN 2624-6120, Vol. 7, no 5, article id 101Article in journal (Refereed) Published
Abstract [en]

Conventional acoustic level metrics quantify infrasonic magnitude but provide limited information about how low-frequency activity is organized in frequency and time. This study introduces Unit Infrasound Activity (UIA), a single-channel signal descriptor for characterizing structured activity in the 0.5–10 Hz band through three components: Strength, Regularity, and Persistence. The method was evaluated using controlled synthetic signals, a reproducible Monte Carlo dataset of 240 randomized signals, a component-ablation analysis, and recordings from contrasting real-world environments. In the Monte Carlo analysis, median UIA was monotonically associated with a predefined synthetic activity proxy (Spearman ρ = 0.855), estimated Persistence closely tracked imposed temporal presence, and dominant-frequency estimation remained accurate for stable periodic signals. Ablation analysis showed that the three components are partially dependent and that simpler combinations emphasize different signal properties, while the full formulation retains sensitivity to magnitude, temporal recurrence, and frequency stability. Application to measured recordings further showed that similar aggregate UIA values can arise from substantially different combinations of Strength, Regularity, and Persistence. UIA is therefore proposed as a complementary continuous descriptor of infrasonic signal structure rather than as a conventional sound-level measure, binary detector, source-identification method, or measure of human response.

Place, publisher, year, edition, pages
MDPI, 2026
Keywords
infrasound; signal processing; persistent activity; unit infrasound activity
National Category
Electrical Engineering, Electronic Engineering, Information Engineering
Identifiers
urn:nbn:se:hig:diva-51208 (URN)10.3390/signals7050101 (DOI)2-s2.0-105054979358 (Scopus ID)
Available from: 2026-10-20 Created: 2026-10-20 Last updated: 2026-11-09Bibliographically approved
Tatar, K., Mattsson, K., Persson, L., Ängskog, P. & Chilo, J. (2025). Infrasound microphone network to monitor wind farm emissions. In: 2025 IEEE International Instrumentation and Measurement Technology Conference (I2MTC): . Paper presented at 2025 IEEE International Instrumentation and Measurement Technology Conference (I2MTC), CHemnitz, Germany, 19-22 May 2025. IEEE
Open this publication in new window or tab >>Infrasound microphone network to monitor wind farm emissions
Show others...
2025 (English)In: 2025 IEEE International Instrumentation and Measurement Technology Conference (I2MTC), IEEE , 2025Conference paper, Published paper (Refereed)
Abstract [en]

Infrasound measurements have evolved from simply identifying sources to analyzing key parameters such as intensity, frequency content, and propagation characteristics in various environments. This study focuses on infrasound emissions generated by wind turbines and presents measurements from three wind farms using a synchronized network of four infrasound microphones. The methodology enables detailed analysis of spatial and temporal variations in infrasound propagation under different operational conditions. Our findings highlight the prominent frequency range of 2–10 Hz, where turbine-generated infrasound is most significant, and reveal spatial variability influenced by turbine layout, environmental factors, and geography. By introducing a synchronized, distributed sensor network, this study provides a tool for gaining new insights into the propagation patterns of infrasound and their potential environmental impacts, offering a robust foundation for optimizing wind farm design and mitigating noise-related concerns.

Place, publisher, year, edition, pages
IEEE, 2025
National Category
Electrical Engineering, Electronic Engineering, Information Engineering
Identifiers
urn:nbn:se:hig:diva-47996 (URN)10.1109/I2MTC62753.2025.11079109 (DOI)001554207900175 ()2-s2.0-105012218400 (Scopus ID)979-8-3315-0501-1 (ISBN)
Conference
2025 IEEE International Instrumentation and Measurement Technology Conference (I2MTC), CHemnitz, Germany, 19-22 May 2025
Available from: 2025-07-24 Created: 2025-07-24 Last updated: 2026-02-19Bibliographically approved
Salm, T., Tatar, K. & Chilo, J. (2024). Real-Time Acoustic Measurement System for Cutting-Tool Analysis During Stainless Steel Machining. Machines, 12(12), Article ID 892.
Open this publication in new window or tab >>Real-Time Acoustic Measurement System for Cutting-Tool Analysis During Stainless Steel Machining
2024 (English)In: Machines, E-ISSN 2075-1702, Vol. 12, no 12, article id 892Article in journal (Refereed) Published
Abstract [en]

This study presents a sound-based tool-wear monitoring system designed to overcome the limitations of conventional methods that focus solely on gradual and predictable wear patterns. The proposed system employs low-cost, high-frequency microphones and advanced signal processing—featuring analog/digital filtering, oversampling, signal conditioning, PLL-based synchronization, and feature extraction (ZCR, RMS)—to capture acoustic emissions during machining. Key innovations include optimized microphone placement, a custom PCB, and real-time data transfer via WiFi to MATLAB for analysis. Using the TreeBagger machine-learning algorithm, the system accurately predicts tool wear, detecting both gradual and abrupt wear patterns. Tested on EN 1.4307 (AISI/ASTM 304L) stainless steel, the system demonstrated robust performance in real-time tool-condition assessment. Its scalable and cost-effective design allows for the integration of additional sensors and features, providing a non-invasive and adaptive solution to enhance machining efficiency and reduce operational costs.

Place, publisher, year, edition, pages
MDPI, 2024
Keywords
tool wear; metal cutting; acoustic signals; real-time monitoring; machine learning
National Category
Mechanical Engineering
Identifiers
urn:nbn:se:hig:diva-46140 (URN)10.3390/machines12120892 (DOI)001384760100001 ()2-s2.0-85213251605 (Scopus ID)
Available from: 2024-12-10 Created: 2024-12-10 Last updated: 2026-02-19Bibliographically approved
Svenningsson, I. & Tatar, K. (2023). Exploring the mechanics of adhesion in metal cutting. The International Journal of Advanced Manufacturing Technology, 127, 3337-3356
Open this publication in new window or tab >>Exploring the mechanics of adhesion in metal cutting
2023 (English)In: The International Journal of Advanced Manufacturing Technology, ISSN 0268-3768, E-ISSN 1433-3015, Vol. 127, p. 3337-3356Article in journal (Refereed) Published
Abstract [en]

The deterioration of the cutting edge during machining influences production cost and productivity. The adhesion is one of the main wear mechanisms. This study delves into the adhesive mechanism in the context of turning, milling, and drilling, focusing on three different cutting materials: 34CrNiMo6, 1.437 stainless steel, and ductile iron. Building upon previous research on the adhesive process in turning, a dynamic model was developed to understand the mechanism further. The results showed that adhesion is a general phenomenon occurring in all tested work materials, but with varying intensity levels. Intermittent cuts did not greatly impact the adhesive mechanism, and cutting data, coolant, and chip breaking also showed little effect. However, the presence of graphite in ductile iron temporarily inhibited adhesion. The source of the adhesive sound was found to be the pivoting movement of the chip as it binds and rips off the cutting tool, leading to a frequency shift upon detachment. The adhesive wear was found to be a thermal mechanism, where chemical reactions between the SiO2 in the work material with the cutting tool caused thermal cracks and low-frequency fatigue.

Place, publisher, year, edition, pages
Springer, 2023
Keywords
Adhesion, Adhesive wear, Frequency, Turning, Milling, Drilling, 34CrNiMo6, Ductile iron, 4307 stainless steel, Uncoated carbide, Coated carbide, SiO2MQL
National Category
Materials Engineering
Identifiers
urn:nbn:se:hig:diva-42116 (URN)10.1007/s00170-023-11681-x (DOI)001005858000002 ()2-s2.0-85163088852 (Scopus ID)
Available from: 2023-06-13 Created: 2023-06-13 Last updated: 2025-10-02Bibliographically approved
Tatar, K. & Svenningsson, I. (2022). Effect of chamfer width and chamfer angle on tool wear in slot milling. The International Journal of Advanced Manufacturing Technology, 120, 2923-2935
Open this publication in new window or tab >>Effect of chamfer width and chamfer angle on tool wear in slot milling
2022 (English)In: The International Journal of Advanced Manufacturing Technology, ISSN 0268-3768, E-ISSN 1433-3015, Vol. 120, p. 2923-2935Article in journal (Refereed) Published
Abstract [en]

The tool geometry is generally of great significance in metal cutting performance. The response surface method was used to optimize chamfer geometry to achieve reliable and minimum tool wear in slot milling. Models were developed for edge chipping, rake wear, and flank wear. The adequacy of the models was verified using analysis of variance at a 95% confidence level. Each response was optimized individually, and the multiple responses were optimized simultaneously using the desirability function approach. The Monte Carlo simulation method was applied to tolerance analysis. All milling tests were conducted at dry conditions; the chamfer width and the chamfer angle varied between 0.1 and 0.3 mm, and 10 and 30°, respectively. Optimal chamfer geometry for minimizing chipping and rake wear was small chamfer width and chamfer angle. The flank wear reached the minimum value for the tool with 0.18 mm chamfer width and 10° chamfer angle. The obtained composite model predicted good edge strength and minimum overall wear when the chamfer was 0.1 mm wide at a 10° angle. Thermal cracks were observed on the tools. They were small on the edges with the finest and least negative chamfer but were more significant on the more negative and greater chamfer. A great chamfer width and chamfer angle also resulted in insufficient chip evacuation. The results show how the edge geometry affects the tool’s reliability and wear and may help manufacturers minimize tool cost and downtime.

Place, publisher, year, edition, pages
Springer, 2022
Keywords
Chamfered tools, Tool wear, Slot milling, Response surface, Multi-objective optimization, ANOVA, Monte Carlo simulations, Tolerance analysis
National Category
Mechanical Engineering
Research subject
no Strategic Research Area (SFO)
Identifiers
urn:nbn:se:hig:diva-37596 (URN)10.1007/s00170-021-08605-y (DOI)000741614800014 ()2-s2.0-85122972396 (Scopus ID)
Available from: 2022-01-11 Created: 2022-01-11 Last updated: 2025-10-02Bibliographically approved
Svenningsson, I. & Tatar, K. (2021). On the mechanism of three-body adhesive wear in turning. The International Journal of Advanced Manufacturing Technology, 113, 3457-3472
Open this publication in new window or tab >>On the mechanism of three-body adhesive wear in turning
2021 (English)In: The International Journal of Advanced Manufacturing Technology, ISSN 0268-3768, E-ISSN 1433-3015, Vol. 113, p. 3457-3472Article in journal (Refereed) Published
Abstract [en]

The paper reveals a hypothesis regarding the adhesive mechanism in metal cutting and its mechanical dynamics. One steel grade, 34CrNiMo 6, 285 HB, and one set of coatings on the cutting tool are reviewed. The adhesive mechanism is a transient vibration, including a feedback system limited by the plastic deformation in the chip. The vibration shows as a cluster of waves with stochastic duration in time. It starts up again after a stochastic lapse of silence. The cycle frequency is around 12.5 kHz and the internal excitation is twice that frequency, as the cutting speed and feed are 200 m/min and 0.2 mm, respectively. The adhesive frequency and amplitude are influenced by the cutting speed and the current wear status. The adhesion is monitored by the sound waves emanating from vibrations in the chip, the part still in the workpiece.

Place, publisher, year, edition, pages
Springer, 2021
Keywords
34CrNiMo 6, Adhesive wear, Frequency, Turning
National Category
Mechanical Engineering
Identifiers
urn:nbn:se:hig:diva-35375 (URN)10.1007/s00170-021-06849-2 (DOI)000626011500002 ()2-s2.0-85102191197 (Scopus ID)
Available from: 2021-03-04 Created: 2021-03-04 Last updated: 2025-10-02Bibliographically approved
Tatar, K., Sjöberg, S. & Andersson, N. (2020). Investigation of cutting conditions on tool life in shoulder milling of Ti6Al4V using PVD coated micro-grain carbide insert based on design of experiments. Heliyon, 6(6), Article ID e04217.
Open this publication in new window or tab >>Investigation of cutting conditions on tool life in shoulder milling of Ti6Al4V using PVD coated micro-grain carbide insert based on design of experiments
2020 (English)In: Heliyon, E-ISSN 2405-8440, Vol. 6, no 6, article id e04217Article in journal (Refereed) Published
Abstract [en]

Tool life prediction is generally of great importance in all metal cutting processes, including milling titanium. In this paper, tool life testing was performed based on full factorial design. The cutting speed and width varied between 100 and 120 m/min, and 10 and 70 percent of tool diameter, respectively. All cutting tests were performed in Ti6Al4V under wet conditions using Physical Vapor Deposition (PVD) coated milling inserts. The wear limit was set to 0.2 mm. The data were analyzed using multiple regression analyses, where the method of least squares was applied. A mathematical tool life model was established. Roughly, for each one percent increase in cutting width, tool life decreases on average by one percent, and an increase in cutting speed by a percent leads to a decrease in tool life by four percent. The adequacy of the model was verified using analysis of variance at 95% confidence level. Tool life contour in cutting width and speed was generated from the model. The results can be used for selecting optimum cutting parameters for providing a desired tool life or maximum metal removal rates for a favored tool life.

Place, publisher, year, edition, pages
Elsevier, 2020
National Category
Mechanical Engineering
Identifiers
urn:nbn:se:hig:diva-32865 (URN)10.1016/j.heliyon.2020.e04217 (DOI)000545793800025 ()32596524 (PubMedID)2-s2.0-85086600777 (Scopus ID)
Available from: 2020-06-19 Created: 2020-06-19 Last updated: 2025-10-02Bibliographically approved
Organisations
Identifiers
ORCID iD: ORCID iD iconorcid.org/0000-0003-1003-1284

Search in DiVA

Show all publications